军事知识服务平台
首页 > 资源导航 > 标准 > 化工 > 合成材料
标准分类
全部
订阅
收起
标准
  • GB/T 10009-1988 - 中外标准 - - 1988/12 - 现行
    本标准规定了丙烯腈-丁二烯-苯乙烯(ABS)塑料挤出板材(以下简称为ABS板材)的产品分类、技术要求、试验方法、试验规则和标志、包装、运输、贮存。  本标准适用于以ABS树脂为基材,用挤出成型方法制得的ABS板材。  本标准不适用于压花的ABS板材。
    尺寸规范板材丙烯腈-丁二烯-苯乙烯共聚物挤压挤压丙烯腈-丁二烯-苯乙烯共聚物板材尺寸规范
  • GB/T 10006-1988 - 中外标准 - - 1988/12 - 现行
    本标准规定了塑料薄膜和薄片在自身或其他材料表面滑动时静摩擦系数和动摩擦系数的测定方法。  本标准适用于厚度在0.2mm以下的非粘性塑料薄膜和薄片。
    薄膜摩擦试验塑料摩擦系数塑料薄膜摩擦试验摩擦系数
  • KS M3699-1988 - 中外标准 - - 1988/12 - 现行
  • ISO 4651-1988 - 中外标准 - - 1988/12 - 现行
    Defines a method measuring the peak deceleration of a mass when it is dropped on a test piece. The test described is intended primarily for quality assurance; however, an annex contains notes to be considered if the test is used to obtain design data. Two figures show typical arrangements.
    冲击试验定义测定英语泡沫橡胶阻尼容量微孔塑料软微孔材料动力试验多孔材料减震材料试验连续冲击试验橡胶试样制备质量管理动态试验包装件阻尼试验塑料试验设备Bump testsCellular materialsDamping capacityDamping testsDefinitionsDeterminationDynamic cushioning performanceDynamic testingEnglish languageFoamed rubberImpact testingImpact testsPackagesPlasticsQuality controlRubberShock-absorbing materialsSpecimen preparationTest equipmentTestingVulcanized rubber
  • ISO 1432-1988 - 中外标准 - - 1988/12 - 作废
    Specifies a static procedure for the materials mentioned over a temperature range from room temperature to approximately -150 °C. Minor revision of the second ecition (ISO 1432:1982).
    试验橡胶硫化橡胶硬挺度低温试验硬挺度试验Low-temperature testingRubberStiffnessTestingTestsVulcanized rubber
  • ISO 265-1-1988 - 中外标准 - - 1988/12 - 现行
    Specifies the series of diameters and the formulae for calculation of the dimensions common to the main types of fittings with spigot ends (socket fittings with curved entries and branches) made of PVC-U.
    塑料管道尺寸未增塑聚氯乙烯下水道废弃物塑料制品管道配件DimensionsPipe fittingsPipelinesPlasticsPlastics productsSewersUnplasticized polyvinyl chlorideWastes
  • ISO 7765-1-1988 - 中外标准 - - 1988/12 - 现行
    Specifies methods for the determination of the energy, that causes plastics films and sheet less than 1 mm in thickness to fail under specified conditions of impact of a free falling dart from a specified height, tha would result in failure of 50 % of the specimes tested. Two methods are described. Method A employs a dart with 38 mm diameter hemispherical head, dropped from a height of 0,66 m, and method B employs a dart with a 50 mm diameter hemispherical head dropped from a height of 1,50 m. The measurement technique is the stairecase method.
    试验试验设备塑料塑料薄膜冲击试验影片AcquisitionCurves (geometry)DamageDefinitionsDrop testsElectronicFilmsFoilImpact penetration testsImpact testingImpact testsImpairment damageInspectionMeasured valuePackagingPackaging filmsPenetration energyPlastic filmsPlastic sheetsPlasticsShock resistanceStilesTemperature dependenceTest equipmentTesting
  • ISO 845-1988 - 中外标准 - - 1988/11 - 作废
    Specification of a method for determining the apparent density or the bulk density of rigid, semi-rigid or flexible cellular plastics and rubbers. If the material to be tested includes skins formed during moulding, the apparent overall density or the apparent core density may be determined. Each test piece shall be of a shape, that its volume can be easily calculated.
  • ISO 2781-1988 - 中外标准 - - 1988/11 - 作废
    Describes two methods. The determination is important in the control of the quality of a rubber compound and in the calculation of the mass of rubber required to produce a given volume of vulcanizate. Does not cover the relative density of rubber. Gravitational forces under different conditions are observed and expressed in units of mass. - Replaces the second edition (ISO 2781:1981).
  • ISO 8013-1988 - 中外标准 - - 1988/11 - 作废
    Specifies a method for the determination of creep in rubber continuously subject to compressive or to shear forces. The standard cannot be used for intermittent deformation of rubber.
回到顶部
选择了条数据