Signal Processing and Slowness Extraction Method for Multipole Acoustic Imaging Logging-While-Drilling Tool
摘要
为了解决随钻多极子声波成像测井仪(Multipole Acoustic Imaging Logging-while-drilling Tool,MPAT)在复杂井眼环境下声波时差提取稳定性差、精度不足的技术难题,依托该仪器的实井实测数据,完成了隔声体滤波区间对时差提取精度影响规律分析,构建了适配 4 个方位正交独立接收阵列的波场分解预处理算法,开展了同井段 MPAT 与斯伦贝谢公司过钻具声波仪器 Thrubit 的时差曲线对比验证,剖析了单一方位阵列与多方位融合处理的时差提取效果差异.研究结果表明:①MPAT 隔声体有效隔声频段为 8~16 kHz,滤波下限低于 8 kHz 会造成纵波时差显著偏离地层真实值,滤波上限高于 16 kHz 对纵横波时差提取无明显干扰,根源为 15 kHz 以上地层声波信号能量大幅衰减;②单一方位接收阵列处理易出现局部井段时差丢失、曲线失真,4 个方位波场分解融合算法可充分利用 48 道接收波形,消除时差缺失段,提升全波列相似相关云图清晰度;③经波场分解预处理后,MPAT 全井段纵横波时差变化趋势、数值与 Thrubit 仪器高度吻合,可精准表征地层纵横波声学特征;④隔声体无法完全阻断钻铤直达波,合理频段滤波是压制钻铤波干扰、分离有效地层波信号的必要预处理手段.结论认为,多方位波场分解预处理方法可稳定、精确提取地层纵横波时差,随钻声波测井时差处理需匹配仪器隔声体隔声区间设置带通滤波参数,滤波低频阈值不得低于隔声有效频段下限.
To address the technical challenges of poor stability and insufficient accuracy in slowness extraction for the Multipole Acoustic Imaging Logging-while-drilling Tool(MPAT)in complex borehole environments,this study uses actual field logging data from MPAT.It analyzes how the filter interval of the acoustic isolator affects slowness extraction accuracy,establishes a wavefield decomposition preprocessing algorithm adapted to four orthogonally oriented independent receiver arrays,compares slowness curves between the MPAT and Schlumberger's Thrubit through-bit acoustic tool across the same borehole interval for verification,and evaluates differences in slowness extraction performance between single-azimuth array processing and multi-azimuth integrated processing.The results show that:①The effective acoustic isolation frequency band of the MPAT acoustic isolator ranges from 8 kHz to 16 kHz.A lower filter cutoff below 8 kHz causes compressional slowness to deviate significantly from the true formation value,while an upper filter cutoff above 16 kHz produces no obvious interference with compressional and shear slowness extraction.This occurs because formation acoustic signal energy attenuates substantially above 15 kHz.②Single-azimuth receiver array processing easily leads to missing slowness data and curve distortion in local borehole intervals.The four-azimuth wavefield decomposition and fusion algorithm fully utilizes 48 receiver waveforms,eliminates slowness gaps,and improves the definition of full-waveform similarity correlation cloud maps.③After wavefield decomposition preprocessing,the trends and magnitudes of full-section compressional and shear slowness from MPAT agree well with those from Thrubit tool,enabling accurate characterization of formation compressional and shear acoustic properties.④The acoustic isolator cannot completely block the drill collar direct wave.Bandpass filtering with a reasonable frequency band serves as an essential preprocessing step to suppress drill collar wave interference and separate valid formation wave signals.It is concluded that the multi-azimuth wavefield decomposition preprocessing method stably and accurately extracts formation compressional and shear slowness.Slowness processing for logging-while-drilling acoustic logging requires bandpass filter parameters matched to the isolation band of the tool acoustic isolator,and the low-frequency filter threshold must not fall below the lower limit of the effective isolation frequency band.