军事知识服务平台
划入角度、衬底类型及制备方法对单层MoS2抗纳米划痕破坏的影响
Effects of Scratching Angle,Substrate Type,and Preparation Method on Nanoscratch Damage Resistance of Monolayer MoS2
摘要 为量化单层二硫化钼(MoS2)在微纳加工与器件封装过程中的抗划擦性能,利用原子力显微镜探针对在 SiO2/Si 和蓝宝石衬底上的单层 MoS2进行纳米划痕实验,研究了划入角度(-30°~30°)、衬底类型(SiO2/Si、蓝宝石)及制备方法(机械剥离法、化学气相沉积法)对单层 MoS2临界破坏载荷与损伤形貌的影响.结果表明,临界破坏载荷对划入角度具有显著依赖关系:在 SiO2/Si 衬底上,划入角度为0°时临界破坏载荷最低(600 nN),临界载荷随划入角度绝对值的增大呈上升趋势;蓝宝石衬底上的临界破坏载荷随划入角度的变化也呈现类似的趋势.蓝宝石衬底上的 MoS2的临界破坏载荷低于相同条件下 SiO2/Si 衬底上的临界破坏载荷.此外,在相同的划擦条件下,机械剥离法制备的单层 MoS2 的临界破坏载荷为 500 nN,明显低于 CVD 样品,且划痕边缘出现卷曲现象.单层MoS2的破坏行为不仅取决于其本征的力学性能,还受到衬底相互作用的影响,通过选择适宜衬底及优化制备工艺,可显著提高单层 MoS2在纳米器件中的抗破坏性能.
Abstract:
Monolayer molybdenum disulfide(MoS2)is a two-dimensional material with promising applications and is widely used in nanoelec-tronic devices,optoelectronic devices,and micro/nanomanufacturing.During practical device fabrication,monolayer MoS2 inevitably undergoes mechanical actions such as scratching,which may cause lattice damage or interfacial failure.However,the mechanical response mechanisms of supported monolayer MoS2 during nanoscratching remain insufficiently understood,particularly with respect to the combined effects of scratching angle,substrate effects,and preparation method.In this study,atomic force microscopy(AFM)-based nanoscratch experiments were conduc-ted to systematically investigate the effects of these factors on the scratch resistance of monolayer MoS2. Monolayer MoS2 was prepared by chemical vapor deposition(CVD)on SiO2/Si and sapphire substrates,while monolayer MoS2 nanosheets were obtained by mechanical exfoliation on SiO2/Si substrates.Sample 1 was a monolayer MoS2 prepared by the CVD method on a SiO2/Si substrate(oxide layer thickness of approximately 280 nm);Sample 2 was a monolayer MoS2 prepared by the CVD method on a sapphire(α-Al2O3)substrate;Sample 3 was a monolayer MoS2 prepared by mechanical exfoliation on a SiO2/Si substrate.The frequency shift differ-ences measured for Sample 1,Sample 2 and Sample 3 were 19.2,19.4 cm-1 and 19.1 cm-1,respectively.The thicknesses of Sample 1,Sample 2 and Sample 3 were 0.7,0.65 nm and 0.7 nm,respectively,confirming that all samples had a monolayer structure.Nanoscratch tests were performed using AFM with a diamond-like carbon-coated probe at 20℃and 30%relative humidity.A single linear scratch was applied at a scanning speed of 1 mm/s.The normal load was increased stepwise from 400 nN in increments of 100 nN until obvious damage occurred.The scratching angle was systematically varied from-30° to+30°. The critical failure load of CVD-grown monolayer MoS2 on the SiO2/Si substrate exhibited a significant dependence on the scratching an-gle.At a scratching angle of 0°,the critical load was the lowest,at approximately 600 nN,corresponding to a groove depth of approximately 0.68 nm.As the absolute value of the scratching angle increased,the critical load increased markedly,reaching approximately 1 400-1 500 nN at±30°.The variation in critical load with angle approximately followed a quadratic relationship with a vertex at 0°.Specifically,the critical load increased monotonically with increasing|θ|,indicating a pronounced direction-dependent mechanical response of monolayer MoS2 during nanoscratching.Monolayer MoS2 grown on the sapphire substrate showed a similar angle-dependent trend,with the lowest critical load also oc-curring at 0°,indicating that this phenomenon mainly originated from the intrinsic in-plane mechanical anisotropy of MoS2.However,at the same scratching angle,the critical loads of the samples on sapphire were generally lower than those of the samples on SiO2/Si.Raman spectros-copy showed that a characteristic Raman peak of MoS2 on sapphire was red-shifted by approximately 0.70 cm-1 relative to that of the sample on SiO2/Si,corresponding to an in-plane tensile strain of approximately 0.28%-0.35%,which reduced the additional load required to reach the critical failure state.In addition,the greater surface roughness of the SiO2/Si substrate provided stress buffering space for the MoS2 layer,whereas the atomically smooth and stiffer sapphire substrate enabled more direct stress transfer to the MoS2 layer,promoting earlier failure.With respect to the preparation method,mechanically exfoliated monolayer MoS2 exhibited a critical failure load of only approximately 500 nN at a fixed scratching angle of 10°.AFM morphology showed pronounced curling and local delamination along the scratch edges,indicating rela-tively weak interfacial adhesion between MoS2 and the substrate.In contrast,CVD-grown MoS2 exhibited stronger bonding with the substrate,enabling the applied load to be transferred more effectively to the substrate and thereby significantly improving its scratch resistance. The nanoscratch failure behavior of monolayer MoS2 is jointly governed by its intrinsic lattice anisotropy,substrate properties,and prepara-tion method.The scratching angle determines the variation trend of the critical failure load.Substrate-induced strain and surface roughness mod-ulate the stress transfer mode.The preparation method affects the damage mode via interfacial bonding strength.This study provides an impor-tant reference for the structural design and process optimization of monolayer MoS2 in micro-and nanoscale devices.
刊 名 材料保护 ISTIC
年,卷(期): 2026, 59(10)
分类号: TG174.4
机标分类号: TN304.055 TB383 TH742
在线出版日期: 2026年11月11日