Fault tolerant control of high speed train actuator based on improved sliding mode active disturbance rejection control
摘要
针对高速列车自动驾驶过程中,执行器部分失效引发牵引系统故障,导致列车速度跟踪精度降低从而威胁列车安全准点运行的问题,提出一种基于改进滑模-自抗扰控制(improved sliding mode active disturbance rejection control,ISM-ADRC)的速度容错控制策略.首先,建立高速列车多质点模型,进而引入执行器故障因子构建列车多质点执行器故障模型;其次,采用新型非线性函数来代替传统的fal函数设计扩张状态观测器,再引入饱和函数设计自适应变速趋近律,将其与非奇异快速终端滑模面相结合,综合得出自适应滑模容错控制律,并通过Lyapunov稳定性理论证明了系统的稳定性.该方法不仅显著减小了控制器的抖振现象,还提高了系统的收敛速度,同时增强了列车在面对参数时变不确定、外部干扰等情况下的鲁棒性,进而提高了执行器部分失效情况下的控制精度;最后,根据CR400BF型动车组参数,分别在无扰动和有扰动的情况下对控制系统进行仿真验证.仿真结果表明,无论是否有外部扰动存在,高速列车的速度跟踪误差均位于-0.1~0.2 km/h的范围内;与无容错控制手段的滑模-自抗扰控制和基于滑模-线性自抗扰控制的容错控制算法相比,本文提出的改进滑模-自抗扰容错控制随着执行器故障程度的变化,速度误差几乎不发生改变且明显小于无容错控制手段的控制器,充分说明了本文所提方法的有效性和良好的自适应性.
To solve the problem of traction system failure caused by partial actuator failure in the process of high-speed train automatic driving,which reduced the accuracy of train speed tracking and threatens the safe and punctual operation of the train,a speed fault-tolerant control strategy based on improved sliding mode active disturbance rejection control(ISM-ADRC)was proposed.Firstly,the high-speed train multi particle model was established,and then the actuator fault factor was introduced to build the train multi particle actuator fault model.Secondly,a new nonlinear function was used to replace the traditional fal function to design the extended state observer.The saturation function was introduced to design the adaptive variable speed reaching law,which was combined with the nonsingular fast terminal sliding mode surface to synthesize the self-adaptive sliding mode fault-tolerant control law.Then the stability of the system was proved by Lyapunov stability theory.This method not only significantly reduced the chattering phenomenon of the controller,but also improved the convergence speed of the system.At the same time,it enhanced the robustness of the train in the face of time-varying parameter uncertainty,external interference,etc.,thus improving the control accuracy in the case of partial actuator failure.Finally,according to the parameters of CR400BF EMU,the control system was simulated and verified in the case of no disturbance and disturbance.The simulation results show that the speed tracking error of high-speed train is in the range of-0.1~0.2 km/h whether there is external disturbance or not.Compared with the sliding mode active disturbance rejection control without fault-tolerant control means and the fault-tolerant control algorithm based on sliding mode linear active disturbance rejection control,the speed error of the improved sliding mode active disturbance rejection fault-tolerant control proposed in this paper hardly changes with the change of actuator fault degree,and is significantly smaller than that of the controller without fault-tolerant control means.This fully shows the effectiveness and good adaptability of the proposed method.