Research on online anti-icing strategies for contact lines considering duration of train tracking intervals
摘要
高速铁路接触线在严寒雨雪气候下易发生覆冰,严重威胁行车安全与供电稳定性.现有研究多基于静态气候条件,未能充分考虑因列车取流产生的周期性焦耳热,以及由此引发的接触线动态温度变化对覆冰过程的关键影响.因此,本文综合考虑了电流热效应与列车运行间隔时长,探究了在线防冰策略的可行性.基于MATLAB构建了接触线三维非稳态传热模型,针对列车在雨雪限速条件下可能出现的多种典型工况(如爬坡、加速/制动、多车共区段及热滑车运行)所对应的电流水平,模拟了不同运行电流下的温升与冷却过程.通过耦合FLUENT与FENSAP-ICE软件,模拟了在不同环境温度、风速及液态水含量(liquid water content,LWC)条件下,接触线的覆冰增长过程,系统分析了覆冰形态、最大厚度及速率等特性.研究结果表明:(1)接触线温度对行车热循环响应敏感.模拟揭示了其瞬态温度变化规律,并确定了从峰值温度冷却至环境温度的"热抑制窗口"时间谱.(2)覆冰生长受接触线凹槽几何特征主导.迎风侧因液滴收集不均,覆冰形态由"三峰凸起"向"单侧月牙形包裹"演变,最大冰厚始终位于这些局部高点.(3)验证了环境温度-5℃、风速9~11 m/s、LWC大于1.4 g/m3为最危险的气象组合,此条件下覆冰速率最快,达到安全阈值的时间被大幅压缩,为风险预警提供了关键依据.研究揭示了列车运营过程中,接触线覆冰生长受行车热循环的影响,呈现"间歇性生长"的特征.通过优化行车组织,构建以"热接力行车模式"为核心的防控策略,依据"防冰安全间隔"动态调整前后列车通过同一区段的追踪间隔,使接触线在列车焦耳热的持续作用下抑制覆冰生长,从而将列车运行过程转化为一种高效、主动的在线防冰策略.
High-speed railway contact wires are prone to icing in severe cold,rainy,and snowy weather,posing serious threats to train operation safety and power supply stability.Existing research is mainly based on static climatic conditions,failing to fully consider the periodic Joule heating caused by train current collection and the crucial impact of the resulting dynamic temperature changes in contact wires on the icing process.For the aim,this study considered the thermal effect of current and the duration of train operation intervals,and explored the feasibility of the online anti-icing strategy.Based on MATLAB,a three-dimensional non-steady heat transfer model for the contact line was constructed.For various typical operating conditions that a train may encounter under rain and snow weather and speed restrictions(such as climbing slopes,acceleration/braking,multiple train sections sharing the same track,and hot sliding train operation),the temperature rise and cooling process under different operating currents were simulated.Furthermore,by coupling FLUENT and FENSAP-ICE software,the icing growth process of contact wires under different environmental temperatures,wind speeds,and liquid water content(LWC)conditions was simulated.The characteristics of icing morphology,maximum thickness,and rate were systematically analyzed.The conclusions are as follows.(1)The temperature of the contact wire is sensitive to the thermal cycling response of the train.Simulations reveal its transient temperature variation patterns and determine the"thermal suppression window"time spectrum from peak temperature cooling to ambient temperature.(2)The growth of ice accretion is governed by the geometric characteristics of the contact wire's groove.Due to uneven droplet collection on the windward side,the icing morphology evolves from"three-peak protrusion"to"single-sided crescent-shaped wrapping",with the maximum ice thickness consistently located at these local high points.(3)The most hazardous meteorological combination has been identified as an ambient temperature of-5℃,a wind speed of 9~11 m/s,and a liquid water content(liquid water content,LWC)greater than 1.4 g/m3.Under these conditions,the icing rate reaches its maximum,significantly shortening the time required to attain the safety threshold and providing critical support for risk early warning.The research further reveals that,during train operation,the growth of contact-wire icing is influenced by the thermal cycling from train running and exhibits an"intermittent growth"pattern.By optimizing train dispatching and implementing the"thermal-relay train operation mode"as the core control strategy,the tracking interval between successive trains passing through the same section is dynamically adjusted according to the"anti-icing safety interval."This allows the contact wire to be continuously heated by the Joule heat generated by trains,thereby suppressing ice accumulation.Consequently,the normal train operation process is transformed into an efficient and proactive online anti-icing strategy.