Time-averaged shear-wave velocity to 30m(VS30)is one of the most widely used parameter for characterizing local site conditions,classifying engineering sites,evaluating site amplification,and developing ground motion prediction models.Direct determination of VS30 generally requires borehole investigation and in situ shear-wave velocity testing to a depth of at least 30m.Such measurements are reliable but costly and spatially sparse,making them difficult to obtain over large regions.Con-sequently,regional VS30 maps are commonly developed from proxy variables such as geology,geo-morphology,and topographic slope.Existing slope-based models are simple and broadly applicable,but a single slope parameter cannot fully represent regional differences in terrain and near-surface materials.Terrain-classification-based models incorporate multiple terrain descriptors,yet they usually assign one representative VS30 value to all locations within the same terrain class,thereby neglecting within-class variability and producing spatially discontinuous estimates at class boundaries.
To address these limitations,this study proposes an improved VS30 estimation method that com-bines terrain features with slope information.Xinjiang,China,was selected as the study area.Three terrain attributes-slope,surface texture,and local convexity-were derived from a 30-arc-second digital elevation model.Following the Iwahashi-Pike terrain-classification scheme,the study area was divided into 16 terrain classes through a nested decision-tree procedure.A total of 4 115 engineering boreholes with measured shear-wave velocity profiles were compiled to develop the model.
Model development involved three steps.First,for each terrain class,65%of the boreholes were randomly selected as the training subset and the remaining 35%were used for validation.This procedure was repeated 1 000 times,and the class-specific representative VS30 value associated with the minimum mean squared prediction error was retained.Second,because several terrain classes contained relatively few boreholes,F-tests at a significance level of 0.05 were used to evaluate whether sparsely sampled classes with similar terrain characteristics could be combined.The results supported merging classes 3 and 4,classes 13 and 14,and classes 15 and 16,whereas classes 1 and 2 were retained separately.Third,within each final terrain group,a logarithmic regression between VS30 and slope was examined.When the slope coefficient was statistically significant,a class-specific regression equation was used to produce continuously varying VS30 estimates;otherwise,the cross-validated representative value was assigned to that terrain group.Statistically significant VS30-slope relationships were identified for seven terrain groups.
The resulting terrain-slope hybrid model was used to generate a regional VS30 map for Xinjiang and was evaluated against two widely used proxy approaches:the WA07 slope-only model and the Yong12 terrain-only model.Compared with the two reference models,the proposed method better represented within-class spatial variability and reduced abrupt changes caused by assigning a single constant value to an entire terrain class.For logarithmic VS30 residuals in the validation dataset,the hybrid model produced a mean residual of 0.018 8,a standard deviation of 0.264 8,a mean absolute error of 0.174 9,and a root-mean-square error of 0.265 2.The corresponding standard deviation,mean absolute error,and root-mean-square error were 0.278 9,0.183 0,and 0.280 7 for Yong12 and 0.328 4,0.260 9,and 0.335 7 for WA07,respectively.An additional assessment based on locally smoothed means and standard deviations yielded a typical standard deviation of 77.42m/s for the hybrid model,lower than 79.06m/s for Yong12 and 83.40m/s for WA07.Site-classification perfor-mance was further examined using the NEHRP B,C,D,and E categories.The terrain-slope hybrid model achieved an overall classification accuracy of 80.85%,compared with 75.56%for Yong12 and 69.79%for WA07.These results demonstrate that incorporating slope-dependent variation within terrain classes can improve both the accuracy and spatial continuity of regional VS30 estimation.The proposed method provides a practical approach for regional seismic hazard and risk studies,rapid site-conditioning mapping,and engineering applications in areas where borehole measurements are limited.Nevertheless,its applicability should be further examined in extensive plains,deep basins,and densely urbanized areas,where the relationship between topography and shallow subsurface conditions may be weak or where buildings and vegetation may bias DEM-derived slope estimates.