Numerical Simulation Study on the Heat Release Performance of a Coupled Embedded Heat Exchanger in Electric Thermal Energy Storage Devices
摘要
固体电蓄热技术通过高电压直供降低配电成本,结合大容量高温蓄热体实现高密度与高品位储能,在蓄热技术中具有明显优势.与传统外置换热器的蓄热系统相比,耦合嵌入式换热器能够简化蓄热系统放热过程,有效提高系统效率.目前对耦合嵌入式换热器的固体电蓄热技术的研究较少,内置式蛇形管换热器的工作条件不同于常规换热器,导致已有的热力计算方法不适用于嵌入式换热器的固体电蓄热技术.本文以放热功率100 kW 级耦合嵌入式换热器的固体电蓄热模块为研究对象,通过Fluent 软件数值模拟放热8 h,探究了蓄热系统放热过程的运行性能,主要考察了运行参数(包括入口流量 qm、入口水温 Tin、蓄热温度 T0)和结构参数(包括换热管管径 d 和纵向管间距 D)的影响.结果表明:qm=1.00 kg/s 的工况系统总放热量较 qm=0.50 kg/s 的工况增加约2.96%,且后期热均匀性较好,但热能输出品质低,导致放热末期供热能力不足,而qm=0.25 kg/s的工况则呈现相反的表现.减小入口水温可增加系统放热量,但出口焓更低,放热末期供热能力不足,当对热能输出品位有要求时,可适当提高入口水温,以"牺牲"少量放热量为代价提高出口焓.T0=1173 K 的工况总放热量较 T0=1073 K 的工况增加13.0%,但牺牲了温度场的均匀性和稳定性.尽管 d=30 mm 的结构在 5h 之后放热表现良好,但在整个放热过程中依然是d=60 mm的结构表现更优且热均匀性更好.D=100 mm 的结构放热量较 D=200 mm 的结构增加了约10.9%,适合短时、大功率放热的场合.通过研究固体电蓄热系统的放热性能,可对换热器的结构布置优化与系统的设计提供指导.
Solid electric thermal storage technology reduces costs of power distribution through high-volt-age direct supply,and achieves high-density and high-grade thermal storage combined with large-ca-pacity and high-temperature thermal storage units,which demonstrates distinct advantages among ther-mal storage technologies.In comparison with thermal storage systems with traditional external heat ex-changers,a coupled embedded heat exchanger can simply the heat release process and effectively en-hance the efficiency of the thermal storage systems.Current research on solid electric thermal storage technology coupled with embedded heat exchangers is relatively limited.The operating conditions of built-in serpentine tube heat exchangers differ from those of conventional heat exchangers.As a result,existing thermodynamic calculation methods are not applicable to this electric thermal storage technology with embedded heat exchangers.This study focuses on a solid electric thermal storage module with an embedded heat exchanger at a heat release power of 100 kW level over 8 hours.Numerical simulations were employed with Fluent software to investigate the operational performance during the heat release process.The effects of operational parameters(including inlet flow mass qm,inlet water temperature Tin,and thermal storage temperature T0)and structural parameters(including heat-exchange tube diameter d and longitudinal tube spacing D)were primarily studied.The results indicated that the condition with qm=1.00 kg/s exhibited an approximately 2.96%increase in total heat release and better temperature u-niformity in the later stage compared to that with qm=0.50 kg/s.However,it was characterized by lower quality of thermal energy output,which resulted in insufficient heating capacity during the later phase of the heat release process.In contrast,the condition with qm=0.25 kg/s showed the opposite characteris-tics.A reduction in the inlet water temperature led to a rise in the total system heat release,while it re-sulted in a drop in enthalpy of outlet and inadequate heating capacity during the later phase of heat re-lease process.If a specific thermal energy output grade is required,the inlet water temperature can be strategically raised to enhance the outlet enthalpy at the cost of a marginal reduction in total heat release.The operating condition at T0=1 173 K achieved a 13.0%higher total heat release compared to that at T0=1 073 K.However,this enhancement involves a compromise in both uniformity and stability of the temperature field.While the structure with d=30 mm performed well in heat release after the fifth hour,the configuration with d=60 mm demonstrated superior performance and better thermal uniformity throughout the entire discharge process.In comparison with the structure with D=200 mm,that with D=100 mm exhibited an approximately10.9%increase in heat release,particularly suitable for applica-tions requiring short-duration,high-power thermal output.The research on heat release performance of solid electric thermal storage systems can provide valuable guidance for both structural optimization of heat exchangers and overall system design.