军事知识服务平台
复杂接缝面参数影响下管片接头刚度智能推算方法
摘要 现有管片接头刚度计算方法无法考虑复杂接缝面构造的影响,导致接缝面构造无法进行量化分析而往往采用经验法设计.为此,提出一种考虑复杂接缝面参数影响的接头刚度智能推算方法.首先,建立可考虑复杂接缝面构造的接头精细化数值模型,分析不同接缝面参数对接头刚度的影响;其次,开展接缝面参数的影响机制研究,分析接缝面参数与接头其他参数对接头刚度的影响,提出基于接缝面影响系数的接头刚度计算方法;再次,讨论不同参数对接缝面影响系数的影响,提出基于注意力机制的深度学习模型方法计算接缝面影响系数;最后,开展 550、600、650 mm 3 种不同厚度管片接头抗弯足尺试验,对所提方法进行验证.研究结果表明:1)接缝面参数对接头刚度的影响显著,不同接缝面参数下接头刚度的最大变化幅度可达 28%~40%;2)在实际工程常用接头其他参数组合范围内,接缝面参数与接头其他参数对接头刚度的影响相互独立,接缝面影响可简化为计算接头刚度的量化系数;3)轴力对接缝面影响系数的影响最大,建立的深度神经网络具有较好的预测效果,最大预测误差为 5.6%;4)所提方法可准确对接头轴力和接缝面参数组合变化时的接头刚度进行推算,与试验结果相对误差不超过 9.0%.
Abstract:
Existing methods for calculating segment-joint bending stiffness fail to account for the effects of complex joint-interface configurations,hindering quantitative evaluation and resulting in experience-based design practices.To address this limitation,an intelligent prediction method for quantifying joint stiffness that explicitly incorporates the influence of complex joint-interface parameters was proposed.First,a refined numerical model capturing complex interface configurations was established,and the effects of different interface parameters on joint stiffness were systematically investigated.Subsequently,the underlying influence mechanisms were analyzed alongside other joint parameters,establishing a stiffness-calculation method based on an interface influence coefficient.Furthermore,the effects of different parameters on this coefficient were discussed,and a deep learning method incorporating an attention block was developed to predict the coefficient across parameter spaces.Finally,full-scale mechanical tests on segment joints with three representative thicknesses(550,600,and 650 mm)were conducted to validate the framework.The results indicate the following:(1)Interface parameters substantially influence joint stiffness,with maximum variations reaching 30%-40%across different interface configurations.(2)Within the ranges of other joint-parameter combinations standard to practical underground engineering,the effects of interface parameters and general structural variables on joint stiffness are independent,allowing for the simplification of interface effects as a standalone quantitative coefficient in joint-stiffness calculations.(3)Joint axial force is identified as the most influential factor governing the interface influence coefficient;the developed deep neural network demonstrates good training and predictive performance,achieving a maximum prediction error of 5.6%on the validation set.(4)The proposed framework enables accurate predictions of joint stiffness under combined variations in joint axial force and interface parameters,with relative errors remaining within 9.0%when benchmarked against full-scale experimental results.
刊 名 隧道建设(中英文) ISTICPKU
年,卷(期): 2026, 46(10)
分类号: U45
机标分类号: TU375 TP391 U451
在线出版日期: 2026年11月9日
基金项目: 52408446:国家自然科学基金WLCY2025:中国中铁股份有限公司科技研究开发计划2025T180903:中国博士后科学基金2024M762693:中国博士后基金面上项目GZB20240632:国家资助博士后研究人员计划,