摘要
针对生态园林树木高位修剪机械化程度低、人工登高作业安全风险高等问题,设计一种仿生爬树机器人.该机器人借鉴灵长类动物交替攀爬行为和电工脚扣抱杆自锁原理,提出"双卡环夹持—螺旋丝杠伸缩—链锯修枝"的总体方案,以实现树干夹持、蠕动式攀爬和侧枝修剪作业.采用三维计算机辅助设计软件UG(unigraphics NX)建立机器人三维模型,利用机械系统自动动力学分析软件(automatic dynamic analysis of mechanical systems,ADAMS)对攀爬过程中的位移、卡环接触力和驱动电机输出响应进行动力学仿真,并基于ANSYS协同仿真工作台(ANSYS workbench)对抱树卡环、丝杠及连接部位进行有限元可靠性分析;同时搭建可编程逻辑控制器(programmable logic controller,PLC)与上位机相结合的分层控制系统,搭载压力反馈模块,实现卡环夹紧状态检测和攀爬动作协调控制.仿真与分析结果显示,机器人可按预定步态完成连续蠕动式爬升,单个攀爬周期爬升距离约150 mm,攀爬过程中未出现明显整体下滑;稳定阶段抱树卡环与树干之间的接触力约960 N,可满足竖直攀爬和驻停自锁要求.有限元分析中,抱树卡环最大应力约46 MPa,低于Q235钢屈服强度235 MPa,安全系数为5.08,关键承载结构未出现明显过量变形.控制系统能够协调3台步进电机完成卡环开合与丝杠伸缩动作,并保证攀爬与返回过程中至少一组卡环保持夹紧状态.该机器人结构方案可行,能够按照预定步态完成蠕动式攀爬动作,关键部件强度满足要求,可为生态园林树木修剪装备的小型化与自动化设计提供参考.
To address the low level of mechanization and the high safety risks associated with manual high-elevation pruning of trees in ecological landscapes,a bionic tree-climbing robot was designed.Inspired by the alternating climbing behavior of primates and the self-locking principle of electrician's pole-climbing devices,an overall configuration inte-grating dual-ring clamping,lead-screw-driven extension,and chain-saw pruning was proposed to achieve trunk grip-ping,inchworm-type climbing,and lateral branch pruning.A three-dimensional model of the robot was developed using unigraphics NX(UG).The displacement,clamp contact force,and drive-motor output responses during the climbing process were investigated through dynamic simulations using the automatic dynamic analysis of mechanical systems(ADAMS).Finite element reliability analyses of the tree-holding clamp,lead screw,and connecting components were conducted using ANSYS workbench.In addition,a hierarchical control system integrating a programmable logic control-ler(PLC)and a host computer was established.A pressure-feedback module was incorporated to detect the clamp tight-ening state and coordinate the climbing motions.The simulation and analysis results showed that the robot could continu-ously climb according to the predefined inchworm-type gait,with a climbing distance of approximately 150 mm per cycle and no evident overall downward slippage during operation.During the stable climbing stage,the contact force between the tree-holding clamp and the tree trunk was approximately 960 N,satisfying the requirements for vertical climbing,sta-tionary holding,and self-locking.Finite element analysis indicated that the maximum stress of the tree-holding clamp was approximately 46 MPa,which was lower than the yield strength of Q235 steel of 235 MPa,corresponding to a safety factor of 5.08.No excessive deformation was observed in the key load-bearing components.The control system coordi-nated three stepper motors to complete the opening and closing of the clamps and the extension and retraction of the lead screw,while ensuring that at least one set of clamps remained engaged during both climbing and descending operations.The proposed robot has a feasible structural configuration,can perform inchworm-type climbing according to the pre-defined gait,and meets the strength requirements of its key components.The design provides a reference for the minia-turization and automation of tree-pruning equipment used in ecological landscapes.