Study on dissolution performance of alumina prepared by nitric acid method from fly ash
摘要
粉煤灰中含有大量的Al2O3,采用酸法工艺所制得的氧化铝纯度高、溶解性能好,是铝电解原料的研究热点.本研究采用硝酸法浸出结合喷枪热解制备氧化铝,并以NaF-KF-AlF3系低温熔盐作为电解质体系,系统考察了粉煤灰硝酸法氧化铝的溶解性能,并与工业拜耳法生产的碱法氧化铝的溶解性能进行了对比,得到以下主要结论.物性分析表明,粉煤灰硝酸法氧化铝中位粒径、松装密度、比表面积、平均孔径均低于传统拜耳碱法氧化铝,微观结构上粉煤灰硝酸法氧化铝疏松多孔,碱法氧化铝颗粒致密紧实.两类氧化铝在氟化物熔盐内饱和溶解度相近,但溶解迁移行为差异显著:粉煤灰硝酸法氧化铝密度小,投入后悬浮于熔盐表层并逐步均匀分散;碱法氧化铝在加入后会快速沉底,并且在底部堆积.粉煤灰硝酸法氧化铝的溶解速度要快于碱法氧化铝,一是粉煤灰硝酸法氧化铝中铝主要以γ-Al2O3相存在,而碱法氧化铝中部分铝以α-Al2O3存在,二是粉煤灰硝酸法氧化铝较碱法氧化铝结构松散,比表面积大.针对粉煤灰硝酸法氧化铝因粒度细、密度过小原因而无法直接用于工业铝电解的问题,可从两条路径进行优化:一是调控硝酸煅烧制备工艺,定向增大氧化铝颗粒粒径与堆积密度;二是革新电解槽加料装备,降低高频加料频次,适配轻质氧化铝粉体.
Fly ash contains a substantial amount of Al2O3.Alumina produced via the acid process exhibits high purity and excellent solubility properties,making it a research focus for aluminum electrolysis raw materials.In this study,an alumina preparation process combining nitric acid leaching with jet torch pyrolysis was employed,utilizing a low-temperature molten salt electrolyte system based on NaF-KF-AlF₃.The solubility performance of alumina derived from fly ash via the nitric acid process was systematically investigated,and its results were compared with those of alkaline-process alumina produced using the industrial Bayer process.The following key conclusions were obtained:physicochemical analyses revealed that the median particle size,loose bulk density,specific surface area,and average pore diameter of fly ash-based nitric acid alumina were all lower than those of conventional Bayer-process alumina;microstructurally,fly ash-based nitric acid alumina exhibited a loose and porous structure,whereas alkaline-process alumina consisted of dense and compact particles.Although the saturation solubility of both types of alumina in fluoride molten salts was comparable,their dissolution and migration behaviors differed significantly:fly ash-based nitric acid alumina,owing to its lower density,remained suspended in the upper layer of the molten salt upon addition and gradually dispersed uniformly;in contrast,alkaline-process alumina rapidly settled to the bottom and accumulated there.The dissolution rate of fly ash-based nitric acid alumina was faster than that of alkaline-process alumina,primarily due to two factors:(1)the aluminum in fly ash-based nitric acid alumina exists predominantly as the γ-Al2O3 phase,whereas in alkaline-process alumina,a portion of the aluminum exists as α-Al2O3;and(2)fly ash-based nitric acid alumina possesses a looser structure and a larger specific surface area compared to alkaline-process alumina.To address the issue that fly ash-based nitrate-process alumina cannot be directly used in industrial aluminum electrolysis due to its fine particle size and insufficient density,two optimization approaches can be adopted:first,adjusting the nitrate calcination process to selectively increase the particle size and bulk density of the alumina;second,upgrading the feed equipment for the electrolytic cell to reduce the frequency of high-frequency feeding,thereby adapting to lightweight alumina powder.