Adaptability of Chemical Flooding in High Temperature,High Salinity and Low Permeability Carbonate Reservoir
摘要
高温高盐低渗碳酸盐岩油藏化学驱面临化学剂活性降低、稳定性变差、注入困难等问题,给实际驱油效果带来不确定性.通过界面张力、接触角、黏度测试、岩心注入性和岩心驱油实验,找到了适用于苛刻环境的表面活性剂和聚合物,明确了聚合物注入性界限,对比了不同体系的驱油效果,确定了适用于低渗透碳酸盐岩油藏的较优化学驱体系与方式.结果表明,两性离子表面活性剂具有更好的耐温耐盐性,在温度78℃、矿化度94 148.0 mg/L和225 068.0 mg/L的条件下,质量浓度为3000 mg/L的EAB溶液能够将界面张力分别降至0.006 mN/m和0.001 mN/m;对比不同两性离子表面活性剂发现,界面张力随其碳链长度增大而减小,增强亲油能力是研选超低界面张力型两性离子表面活性剂的有效方法.常规HPAM在温度78℃、矿化度94 148.0 mg/L和225 068.0 mg/L水中难以长期稳定,老化50 d黏度保留率不足5%;SAV10和SAV55聚合物能够保持较好稳定性,老化90 d黏度保留率分别在80%和60%以上.在渗透率为3.4×10-3 μm2的岩心中,SAV10注入压力梯度持续升高,不能稳定,难以注入;9.6×10-3 μm2岩心中,浓度≤200 mg/L(0.81 mPa·s)的SAV10注入压力梯度能够稳定,具有一定注入性;21.0×10-3 μm2岩心中,浓度≤1000 mg/L(≤2.8 mPa·s)的SAV10注入压力梯度可较好稳定,可注入.渗透率10×10-3 μm2左右岩心驱油表明,单一表面活性剂驱采收率增幅有限,注入0.3 PV 3000 mg/L EAB溶液提高4.4个百分点,注入1.0 PV提高8.1个百分点;聚合物驱采收率增幅相对明显,为16.4个百分点;表面活性剂泡沫能够实现超低界面张力洗油与升压扩大波及的协同,采收率增幅最高,为27.4个百分点;SP复合体系驱采收率增幅次之,为24.0个百分点.
Chemical flooding in high-temperature,high-salinity and low-permeability carbonate reservoirs faces challenges such as reduced chemical activity,poor stability,and difficult injectivity,which introduce uncertainty into oil displacement performance.This study conducted experiments on interfacial tension,contact angle,viscosity,core injectivity,and core flooding to identify surfactants and polymers suitable for harsh environments,clarified polymer injection limits,and compared the oil displacement performance of different chemical systems.The results demonstrated that amphoteric surfactants exhibited superior thermal and salt resistance.At the temperature of 78℃,EAB solutions at 3000 mg/L reduced the interfacial tension to 0.006 mN/m and 0.001 mN/m in brines with salinities of 94 148.0 mg/L and 225 068.0 mg/L,respectively.Comparative evaluation of amphoteric surfactants revealed that interfacial tension decreased with increasing carbon chain length,indicating that enhancing lipophilicity was an effective strategy for developing ultra-low interfacial tension amphoteric surfactants.Conventional HPAM showed poor long-term stability at 78℃in 94 148.0 mg/L and 225 068.0 mg/L brines,with viscosity retention below 5%after 50 days of aging.In contrast,polymer SAV10 and SAV55 demonstrated better stability,retaining more than 80%and 60%of their viscosity after 90 days of aging,respectively.In a 3.4×10-3 μm² core,the injection pressure gradient of SAV10 solutions increased continuously without stabilization,making injection difficult.In a 9.6×10-3 μm² core,SAV10 at concentrations≤200 mg/L(0.81 mPa·s)achieved a stable injection pressure gradient,showing acceptable injectivity.In a 21.0×10-3 μm² core,SAV10 at concentrations≤1000 mg/L(≤2.8 mPa·s)achieved good pressure gradient stability and injectivity.Core flooding tests in cores with permeability around 10×10-3 μm² showed that surfactant flooding alone showed limited incremental oil recovery,with a increment of 4.4 percentage point after injecting 0.3 PV EAB solution with mass concentration of 3000 mg/L,and 8.1 percentage point with injection of 1.0 PV EAB solution.Polymer flooding achieved a more notable incremental recovery of 16.4 percentage point.Surfactant foam flooding delivered the highest incremental recovery of 27.4 percentage point by combining ultra-low interfacial tension oil washing with mobility control and sweep expansion.The SP composite system provided the second-highest incremental recovery of 24.0 percentage point.