军事知识服务平台
铝熔体在多孔预制体渗流行为的数值模拟
Numerical simulation of infiltration behavior of aluminum melt in porous preforms
摘要 [目的]揭示燃料颗粒多孔预制体内铝熔体的渗透演化规律,实现压力浸渗制备铝基弥散燃料元件的工艺调控.[方法]构建燃料颗粒多孔介质模型,采用相场法,对铝熔体在多孔预制体中的浸渗过程进行孔隙尺度模拟,系统分析浸渗压力、熔体黏度、接触角等参数对铝熔体浸渗行为的影响规律.[结果]入口浸渗压力越低,熔体流动优势通道现象越显著,浸渗饱和度越低;低黏度熔体能在极短时间内完成对多孔介质孔隙的填充,且浸渗饱和度较高,但也会因缺少黏性剪切的稳定流动作用而使孔隙空间内更多气体被困于孔道内部难以排出;毛细驱动力与入口浸渗压力呈现协同效应.[结论]熔体浸渗过程中的钉扎效应与弯液面几何形貌演化是导致孔隙内形成孤立气泡的主要因素.
Abstract:
Objective Melt infiltration is a favorable manufacturing route for fabricating aluminum matrix dispersed fuel elements.Using preform skeletons and melt infiltration densification,this method effectively overcomes the limitations of conventional manufac-turing routes,such as low fuel volume fraction,uneven fuel distribution,and poor densification.Nevertheless,the transient fill-ing mechanism of the infiltration front in porous media and the quantitative correlation between infiltration pressure and satura-tion remain insufficiently understood.Therefore,clarifying the intrinsic relationship between aluminum melt infiltration behav-ior and its key influencing factors,and revealing the effects of infiltration processes and melt physical properties on infiltration characteristics are of great significance for developing advanced fabrication technologies for high-performance aluminum matrix dispersed fuels. Methods In this study,the phase-field method was adopted to characterize two-phase flow behaviors.The Cahn-Hilliard equa-tion was applied to capture the evolution of the interface position,where the chemical potential was defined as a function of mix-ing energy density and interface thickness control parameters.A porous medium model consisting of fuel particles was estab-lished,and pore-scale simulations of aluminum melt infiltration were carried out.The feasibility of the proposed model was veri-fied against experimental data. Results and Discussion Under external pressure,the melt preferentially advanced toward both sides.After the displacement fronts on both sides reached a certain depth,the melt gradually infiltrated and filled the intermediate region.When the melt flowed into dead-end pores,the liquid meniscus ruptured,and newly formed liquid-gas interfaces encapsulated residual gas within pores to form discrete isolated bubbles.When two opposing menisci converged and coalesced,the convex liquid surface could not fully spread,and residual gas was trapped by pinned liquid interfaces to form permanent pore void defects.For porous architectures featuring large cavities confined by narrow pore throats,interfacial pinning readily occurred,which suppressed effective gas evacuation from internal cavities and ultimately generated isolated bubbles.In the late infiltration stage,pressure fluctuations exhibited a lower frequency.A plateau appeared on the flow velocity curve in the late stage,indicating that the melt was trapped in narrow pores and flowed steadily along dominant flow channels at a nearly constant flow velocity.Sufficient driv-ing pressure in the early infiltration stage yielded high infiltration saturation.Saturation fluctuated in the middle and late stages,mainly caused by Haines jumps induced by driving pressure attenuation.In the final stage,the discrepancy in infiltration satura-tion between samples under different inlet pressures became pronounced.Low-viscosity melts could fully occupy pore voids within an extremely short period.However,the absence of flow stabilization from viscous shearing readily triggered disordered channeling during melt infiltration.This trapped a greater amount of gas inside pore channels that could not easily escape,thereby deteriorating infiltration densification.When aluminum melt exhibited poor wettability with pore wall substrates,the liq-uid front became pinned at narrow pore throats,and a large external pressure was required to overcome pinning.In contrast,sys-tems with favorable melt wettability against pore walls required much lower external pressure for depinning,and the depinning process proceeded spontaneously.Poor wettability resulted in larger differences in displacement front depth,which continuously expanded as the overall infiltration depth increased.For strongly wetting interfaces,the differences in displacement front depth increased in the early infiltration stage.In the later stage,the average throat radius of unfilled pores decreased,the capillary driving force increased,and the differences in displacement front depth declined. Conclusion In this study,pore-scale numerical simulations are conducted to characterize aluminum melt infiltration within porous preforms using a constructed packed-particle porous medium model.The results show that isolated bubbles during melt infiltration originate from meniscus evolution induced by pore geometric configurations and interface pinning effects.Under low inlet infiltration pressure,the dominant seepage channel is preferentially formed,which reduces overall infiltration saturation and increases the occurrence probability of Haines jumps.Low-viscosity melts can rapidly fill porous voids and reach high satu-ration.Nevertheless,the lack of flow stabilization from viscous shear induces chaotic channeling.A large amount of residual gas remains trapped inside pore channels and cannot escape,impairing the uniformity of pore filling.When capillary force acts as flow resistance in melt-solid systems,the liquid front is prone to pinning at narrow pore throats,and high external pressure is required to achieve depinning,resulting in non-uniform infiltration.At strongly wetting interfaces,capillary force cooperates with external pressure to promote infiltration,and less external force is needed for depinning.However,isolated gas bubbles easily form when melt flows through large cavities surrounded by tiny pore throats.
刊 名 中国粉体技术 ISTIC
年,卷(期): 2026, 32(5)
分类号: TB4 TB333
机标分类号: TE311 U455.43 TG146.21
在线出版日期: 2026年10月30日