军事知识服务平台
多形态散料离散元参数的协同标定方法与验证
Collaborative calibration method and verification of discrete element parameters for multi-morphology bulk materials
摘要 [目的]建立一套适应多种类和形态的物料的离散元参数协同标定方法,构建高保真散料参数数据库.[方法]通过物理实验测量各种类和形态的物料的粒径分布、休止角和堆积密度;根据物理实验实测参数和待标定参数范围,采用颗粒缩放模型确定离散元仿真试验所需的仿真参数值;通过Plackett-Burman试验、最陡爬坡试验、Box-Behnken试验以及回归方程进一步确定最优参数组合;根据最优参数组合进行仿真试验,确定仿真休止角和仿真堆积密度,确定与物理实验测定值之间的仿真误差,实现对离散元参数标定方法的验证.[结果]在建立颗粒状、粉尘状和混合状散料的离散元颗粒模型时,黄豆、玉米、小麦和水稻缩放因子为1,粉煤灰、石灰粉、硫酸铵及散煤样品缩放因子为5.散料与散料之间的滚动摩擦系数对不同种类散料的休止角的影响率为66.1%~99.7%,显著高于泊松比、切变模量、散料与散料之间的恢复系数、散料与钢之间的恢复系数、散料与钢之间的滚动摩擦系数、Johnson-Kendall-Roberts(JKR)表面能等参数的影响率,JKR表面能对粉尘状物料的影响率为12.9%~20.9%.各散料回归模型的决定系数R2均大于0.95,信噪比均大于4.仿真休止角与实验值的相对误差均小于3%,仿真堆积密度与实验值的相对误差均小于7%.[结论]休止角回归模型拟合度良好,各散料的仿真堆积轮廓与实验堆积形态高度吻合,所标定的参数能够准确复现真实散料的宏观流动行为.
Abstract:
Objective Based on physical experiments and simulation tests,a collaborative calibration method for discrete element param-eters is established for materials with different types and morphologies,and the particle scaling effect is taken into account.A high-fidelity parameter database for bulk materials is also constructed. Methods The particle size distribution,angle of repose,and bulk density of materials with different types and morphologies were measured through physical experiments.Based on the measured parameters and the ranges of the parameters to be cali-brated,a particle scaling model was used to determine the simulation parameter values required for discrete element simulation tests.The optimal parameter combination was further determined using Plackett-Burman tests,steepest ascent tests,Box-Behnken tests,and regression equations.Simulation tests were then conducted using the optimal parameter combination to deter-mine the simulated angle of repose and bulk density.The simulation error between the simulated and experimental values was calculated to validate the calibration method for discrete element parameters. Results and Discussion When discrete element particle models were established for granular,powdery,and mixed bulk materi-als,the scaling factor λ was set to 1 for soybean,maize,wheat,and paddy rice,whereas it was set to 5 for fly ash,lime pow-der,ammonium sulfate,and loose coal samples.The influence rate of the rolling friction coefficient between bulk materials on the angle of repose of different bulk materials was approximately 66.1%-99.7%,which was significantly higher than those of Poisson's ratio,shear modulus,restitution coefficient between bulk materials,restitution coefficient between bulk material and steel,rolling friction coefficient between bulk material and steel,and JKR(Johnson-Kendall-Roberts)surface energy.The influence rate of JKR surface energy on powdery materials was approximately 12.9%-20.9%.The coefficients of determination(R2)of the regression models for all bulk materials were greater than 0.95,and the signal-to-noise ratios were greater than 4.The relative error between the simulated and experimental angles of repose was less than 3%,and that between the simulated and experimental bulk densities was less than 7%.The relative errors between simulated and experimental bulk density and angle of repose of all bulk materials were within a reasonable range. Conclusion The angle-of-repose regression model shows a good fit and can accurately predict the variations in the angle of repose with significant influencing factors.The bulk density simulation test effectively reproduces the experimental process of bulk materials from the initial state through falling to final deposition state.The simulated deposition profiles of all bulk materials are highly consistent with experimental deposition morphologies,indicating that the calibrated parameters can accurately reproduce the macroscopic flow behavior of real bulk materials and that the parameter values are reasonable and reliable.
刊 名 中国粉体技术 ISTIC
年,卷(期): 2026, 32(5)
分类号: TB4 TP391.9
机标分类号: J524 TP3 R283.6
在线出版日期: 2026年10月30日